How to reduce water consumption in the toilet? What type of toilet saves water as much as possible How to reduce hot water consumption

Controlling water consumption in a home is not only budget saving, but also a tribute to natural resources. By reducing the consumption of water in the toilet and for household and drinking needs, you can save more than a thousand liters in just a month. At the same time, life will not become less comfortable.

Reasons for water consumption

One of the main reasons is devalued resources and habits of not turning off the tap when water is not needed. It depends on the person, therefore it is quickly solved by the method of re-education.

The plumbing device allows excess water. For a comfortable life, a weaker pressure of the jet from the tap and a reduced volume of the toilet bowl are enough. This is also easy to fix with simple tricks.

The reason requiring attention is plumbing leaks. This hits not only the budget, but also the condition of the devices. So the bathtub or toilet quickly becomes covered with limestone, which is very difficult to remove. The high humidity in the house starts a fungus.

How to reduce toilet water consumption

The average toilet cistern holds 8-9 liters of water. For flushing, 6 liters are enough. This difference is easy to fix with your own hands.

An uncomplicated way to reduce the volume of the tank is a container with water or something heavy. A 1.5-2 liter plastic bottle is suitable. We fill it with water, sand or something else, tighten the lid tightly. We place the container in the tank so that it does not touch the drain mechanism. Ready! The amount of water to fill the toilet has now decreased.

After placing the bottle in the cistern, Miss Clean magazine advises to check if the toilet flushes well. If there is not enough water, it is recommended to choose a smaller container.

Important
What you shouldn't do is put a brick in the cistern. It tends to dissolve, and this is fraught with clogging of the sewage system.

Water for household and drinking needs is consumed by us in unmeasured quantities. Train yourself to turn off the tap when you brush your teeth or shave. In a couple of minutes, about 10 liters of useless water flows out, and this happens every day. The same advice applies to washing hands and dishes. Only open the tap for rinsing.

Tap nozzles are an excellent solution that allows you to reduce water consumption by a third or even 2 times. With the mesh nozzle, the jet from the tap does not get thinner, but all thanks to air bubbles. You can wash your hands and dishes as usual under high pressure. A similar nozzle is installed on the shower hose. Another plus of this nozzle is the reduction in the amount of splashes and noise reduction when using water.

Place mixers with a common lever. It is much easier to adjust the water temperature this way than with two taps. It takes time to set up, and money goes down the drain.

Several Yet simple tips for savings that will not bother anyone:

Pour as much water into the kettle as you need at the moment. Repeated boiling is harmful to the appliance, we still drain the unused water.
First soak the burnt dishes with boiling water, and then wash.
Do not machine wash a pair of socks or T-shirts if you can wait until the drum is full.
It is enough to rinse some dishes, and not apply detergent to them. More water is required to rinse off the foam.

How to reduce hot water consumption

Since the New Year, prices for housing and communal services have soared once again. And therefore, it makes sense to save at the expense of those resources that are supplied to the house by the counters. Hot water is very expensive. Install a tank water heater in the bathroom or toilet.

Modern models consume little electricity (water is rarely heated, mostly - it remains hot due to the design of the tank). For a family of three or four people, a 30-liter device and a mode not higher than 60 ° are enough. Especially if you follow the little tricks: turn off the water while massaging your head with shampoo or rubbing with a massage washcloth, while working with a toothbrush, etc.

Conserving water doesn't mean being greedy. Simple installations will help to resolve the issue imperceptibly. For the most advanced, there is a water-saving Appliances- washing machines and dishwashers, various mixers, toilet cisterns with two flush modes. All this, along with simple and inexpensive life hacks, should become part of the life of a person interested in ecology and finance.

In this article, we will discuss toilet flushing - how to adjust it to reduce flush water consumption; what to do if the tank is running through; because of which the toilet may not flush well.

Unfortunately, we cannot consider all the designs of the cistern and toilet bowl within the framework of one article; we will focus on the most common design - the domestic bottom cistern.

This is not quantum physics. But you have to think

Reducing flush volume

Why is it needed

The toilet and cistern provide up to half of the total water consumption. Another 25 percent is each for washing dishes and taking a shower.

If water is very expensive in your region, it is logical to save it. The most obvious way is to reduce the amount of water used for each flush of the cistern.

Tip: Many valve kits allow for more flexible water use.

The tank is equipped with two buttons; pressing one of them results in flushing using the entire volume of water (usually 8 liters), pressing the second one - to the consumption of half of this amount.

Solution

Adjusting the flush of the toilet in this case comes down to adjusting the amount of water in the toilet at the moment when the valve shuts off the water.

The operation of the float valve is very simple: water is collected, the float floats up and a lever sets in motion a brass or plastic plug, which closes the nozzle supplying water with a rubber gasket.

How to adjust the float in the toilet so that it turns off the water earlier?

If the lever is brass- just fold it over. By raising and lowering the float, it is easy to see in what position it blocks the water.

Here, the entire valve mechanics are shown very clearly. To cut off the water earlier - just bend the brass lever (No. 6 in the diagram)

If you have a newer set of fittings and the lever is made of plastic- examine it carefully.
To position the float, either a fixing screw is used, which allows you to change the bend of the lever, or a simple plastic ratchet, which fixes the float in one of the positions.

One of the alternative designs. It is usually sufficient to simply inspect the valve closely to understand the method of adjusting it.

Eliminate tank leakage

Why eliminate it - I think it's understandable. This is a useless waste of water, and constant condensation on the surface of the tank and pipe, and a toilet bowl that is quickly contaminated with rust and lime deposits.

Reason 1

The tank overflows because the float valve does not shut off the water in time. Water flows through the overflow.

Solution 1

How to adjust the toilet cistern in this case? Exactly the same as in the previous case. Bend the float arm so that the water is cut off at a level a couple of centimeters below the overflow.

Please note: in houses where they stand and operate on a pumping timer (pumps for raising water to the upper floors at the peaks of water withdrawal), the water pressure during the day can vary greatly.

It makes sense to adjust the water pressure when pumping when it is at its maximum.

Then, at a lower pressure, the float will cut off the water at a level two to three centimeters lower.

Reason 2

The pear blocking the drain in the cistern has lost its elasticity and no longer completely blocks the water. Water flows from the toilet cistern constantly, even when it is not full.

Solution 2

Adjusting the toilet bowl drain in this case can be reduced to a simple operation: add any weight to the pear... We will hang on top of it a couple of nuts, a cast-iron sleeve or a lead sinker with a hole in the center.
An alternative to this appendage is the replacement of a pear... Turn off the water on the tank and unscrew the old pear to take it to the store as a sample: the seller may not heed your complex pantomime and not understand what you need from him. Regular right-hand thread on the pear and stock; the stem will have to be held with pliers.

In the photo is the same pear. Here it has just been replaced along with the stem and mount.

The toilet doesn't flush well

How to adjust the toilet if the flush has deteriorated sharply from a certain point?

Cause

If the toilet began to flush badly abruptly, literally in one day, and the flush does not depend on how much water is in the cistern - most likely, something got into the outlet of the cistern or the drain of the toilet itself. You yourself understand that adjusting the water level in the toilet cistern will not help here.

Most often, the rubber hose from the float valve becomes such an object. It is put on the outlet of the valve so that water is drawn into the tank without sound. Rubber loses its elasticity over time; the hose slides off the valve and goes on a single float.

Usually, after the next flush, the regatta ends somewhere between the release of the cistern and the bowl of the toilet. And since water passes through a piece of rubber extremely poorly, we immediately face the consequences.

However, if the tank is without a lid, sometimes the most unexpected objects can be found in the tank outlet. The imagination of preschool children is especially boundless.

And in this case, do not rush to despair

Solution

We shut off the water to the tank.
We raise the pear and look under it. If we see a foreign object and we can pull it out, great, the adjustment of the toilet barrel ends there.
If the hose or any other debris is visible, but not accessible for extraction, look for tweezers.
Finally, if you still can't get to the source of our troubles, alas, you will have to remove the tank. We take the pliers and an adjustable wrench and unscrew the bolts between the tank and the shelf.

Carefully raise the cistern (the flexible liner can be left on) and put it on the toilet; to avoid chipping, it is a great idea to use a rag or towel. We extract from the recess in the shelf what should not be there.

Removing the cistern, it is easy to get to the toilet bowl drain

If your tank has a separate shelf that is not part of the toilet, you can get to the problem area by removing the cuff between the shelf and the tank.
It is better to unscrew before this the bolts securing the shelf to the toilet bowl: otherwise it will be difficult to remove the cause of the blockage.

The cuff will most likely need to be replaced: as already mentioned, the rubber loses its elasticity over time, and the cuff is likely to leak after re-insertion.

If you have such a design of the tank and the shelf, you can get to the blockage through the gap between the shelf and the toilet

After the flush device for the toilet cistern is cleaned and the cistern is assembled, turn on the water and make sure that the drain is working properly and there are no leaks anywhere. This completes the adjustment of the toilet cistern.

Conclusion

Let us remind you once again: we in no way claim to be complete coverage of problems or types of fittings. New devices with fundamentally different mechanics and their own typical problems are constantly appearing on the market.

For this tank, for example, both the float adjustment and the replacement of the bulb will be completely different.

Oftentimes, however, a careful study of the instructions can help. Good luck with the repair!

Home comfort depends on many factors that are not always visible. There are objects in the house that play an important role, but at the same time we attach little importance to them, at least while they are working. This is the case with the toilet. This is an important household unit, the failure of which can destabilize the situation in the family. Therefore, it is important to be able to cope with the settings, to make initial repairs.

It is worth figuring out how you can regulate the water level, what to do if it falls or rises. To do this, we will give examples with photos, as well as video instructions.

Reducing the drain volume

Most modern toilets are equipped with two-button systems. What does it do? First of all - less water consumption, since one button allows you to use only part of the water in the tank. It is no secret that the water used by the toilet is actually up to half of all household water consumption. Added to this indicator is washing dishes and bathing.

Therefore, it is very important not only to use a two-button system, but also to take care of optimizing the amount of water that is drawn into the tank. Moreover, most modern systems provide a fairly smooth adjustment. Whereas previously it was necessary to manually bend the float lever in order to achieve a decrease in the level of water collection, the systems allow this to be done by rotating a plastic screw.

Let's remind how the float valve works. Water goes down from the tank to the bowl, while the water supply in the tank is replenished from the plumbing system, the float gradually floats up, forcing the cork with a rubber bulb to move, blocking the water.

If you are using a brass lever system, you need to bend it down and then test how much water will be drawn.

Increase in water volume

It should be noted that savings most often determine efficiency. And if the water level in the tank has dropped significantly, saving water, you can make sure that sewage from the thicket will not be well washed off. In such cases, you have to drain the water several times, which, undoubtedly, has nothing to do with savings. Therefore, we need a middle ground.

In this case, you need to act in the same way as in the previous one, only this time it is necessary to tighten the plastic screw or bend the brass lever to raise the water level.

Poor flush

What if the flush deteriorated sharply, but there were no obvious prerequisites for this? It is likely that something has gotten into the drain or outlet of the tank, which is preventing the water from moving. Of course, it is useless to regulate the liquid level: whether it has decreased or increased, it does not really matter.

Often this foreign object is the hose from the valve. It is used to reduce noise when filling the tank with water. As the material loses its quality over time, the rubber can slip off the valve, causing it to float and then get stuck in the working elements of the toilet. The consequences of this are drainage problems.

The rest of the options for what objects can get into the tank depend on whether the lid is installed on it. If it is not there, then anything can get into the cistern, especially if there are children at home who already use the toilet.

The problem is solved in this way:

It is necessary to turn off the water, drain it from the tank and remove the lid (by default, we assume that it is present). In push-button systems, you first need to unscrew the ring counterclockwise, remove the button, and then carefully remove the cover.
Next, you need to look under the pear, whether there are any foreign objects under it. If there is one, removing it will fix the problem.
Sometimes, among the systems located in the tank, you can't stick your hand in and get the hose out. You need to prepare tweezers with which you can do this.
If you cannot get the hose, you will have to remove the tank.
We unscrew the bolts that hold the tank on the shelf.
Carefully remove it, put it on a soft and flat surface, and then we take out a foreign object.
After that, you need to collect everything, proceeding in the reverse order.

Eliminating the leak

There are two reasons here, which means there are two ways to solve the problem.

First option

Consider the first option, in which the water level has risen so much that it flows through the overflow. If a lever is used, it must be bent to lower the float, which means that the volume of water will be reduced, it will not rise above the critical level: a couple of centimeters below the overflow. The push-button system is adjusted in the same way, only instead of a lever, a plastic screw is twisted.

And here you need to take into account one nuance. If the regulation takes place in a private house where there are pumps that pump water in time, the pressure in the water supply system can vary greatly. Therefore, the tuning must be done when it is at its peak. This will avoid exceeding the water level in the reservoir, even if the pressure in the system is at its maximum.

Second option

Consider the second option, in which the water level in the tank drops. In order for it to increase and the flow to stop, you need to determine the reasons. Leaks are often the result of damage or wear to the bulb. Over time, the material can lose its elasticity, which will cause leakage.

Everything is solved in this way:

A temporary solution is to add a load. Multiple nuts can be used. By making the structure heavier, the pear will press the tank drain hole more tightly.
A more thorough and effective way is to replace the pear. You need to turn off the water, get the pear, and then replace it with a new one. There is one recommendation: you should only go to the store with an old pear, as this will allow you to choose an exact new copy that is 100% suitable for our design.

Outcomes

As you can see, if the water level does not correspond to the norm, this can be corrected, and in modern systems, this does not require special efforts. To decrease or increase the level, you need to twist the plastic threaded screw. If you adjust in one direction - the level rises, in the other - falls. In older systems, it is enough to bend the brass lever to change the position of the float.

In connection with the annual increase in taxes on housing and communal services, many began to think about how to save on some things, in particular, on the toilet. We will tell you further how to reduce the consumption of water in the barrel of the bathroom in order to pay less on tariffs and feel the real monetary benefit from this case.

Reasons for overconsumption of water through the tank and ways to save it

The water in the toilet is consumed as a result of a leak. As a rule, in the event of a breakdown, the equipment breaks down and begins to leak, hitting the budget. In addition, one of the main reasons for consumption is frequent and wasteful use.

Sometimes, in some cases, the toilet is connected to the sink and the consumption depends on the uneconomical use of the washbasin, the habit of not turning off the tap when there is no need for liquid. Consider the proven 7 methods of how to reduce the water consumption in the toilet cistern.

1. Use less water

On average, 6 liters of water is needed for flushing, and the average tank contains 9 liters. To prevent it from recruiting liquid, it is necessary not to press the flush button to the end. So, on average, 2-3 liters will be saved. An impressive amount of savings will come out in a month.

2. Reduce the volume of the tank

This can be done by placing a plastic bottle of water or sand in it. However, it must be placed so that the drain mechanism does not close, and the bottle does not interfere with the operation of the entire system.

3. Install the special nozzle

Today, such nozzles are sold both on the faucet and on the toilet. They control the water supply. Interestingly, it reduces splash and noise when using water.

4. Do not use the toilet button

Draw on your own the amount of water that is sufficient for rinsing. This is an old method that almost no one uses anymore.

5. Replace the tank with an economical option

When buying a bathroom, you need to pay attention to models that have an economical tank. Such devices save up to 5 thousand liters per year and, thus, reduce the number of monthly installments.

6. Eliminate the leak

If it is available by calling a plumber or by proven methods from craftsmen. As a rule, the bulb for overlapping the drain in the cistern loses its elasticity. All that is needed is to hang the sinkers from both sides of it. In some cases, it is necessary to change it.

7. Adjust valve and float

Adjust so that the tank is not full. This will lower your meter readings and help save money.

In general, if you wish, you can always reduce the consumption of light, gas and even the consumption of liquid in the bathroom, which affects the total amount of payment for utility bills. The main thing is to approach this issue competently and use the above simple tips.

This guy knows a lot about saving! An ingenious way to pay a lot less for water.

Judgment day comes every month, bringing some upsetting. Paying the bills again? Constantly increasing utility rates despair even those who make good money.

Nobody wants to overpay! In such conditions, the most reasonable solution is to save ...

By saving water and electricity, you will not only spend less money, but also do a good deed by saving environment... Water reserves on the planet are not endless ... The method that you will see in the video will help you save a couple of tens of liters of water per month without any effort. You just need to open cistern and put there plastic bottle filled with water.

The volume of the tank will decrease, but not enough to affect the quality of its work. Probably, this American guy has ancestors clearly from the USSR, and no one can compare with such people in ingenuity in everyday matters!

One of the main reasons is devalued resources and habits of not turning off the tap when water is not needed. It depends on the person, therefore it is quickly solved by the method of re-education.

2. Adjustment of the valve

Reducing drainage is also achievable with mechanical measures. They boil down to adjusting the float in the toilet so that it blocks the liquid earlier. The brass lever just needs to be bent. Raise and lower the float - you will see in which position it shuts off the water supply.

For plastic fittings, use a mounting screw or ratchet of the same material. These parts fix the float in a position that prevents excess flow. As a result, the tank will not be completely filled, which will reduce the meter's performance and save money.

How to reduce water consumption in a toilet cistern

Few people think about how much water goes away when the toilet is flushed. Considering that, on average, a person visits the toilet 3-4 times a day, and the cistern of a modern toilet bowl has a volume of 8 liters, it is easy to calculate how many liters of water are consumed per day. Experts advise not to drain the toilet completely, leaving half the tank full. This can be done by adjusting the tank drain valve so that water does not fill the tank completely. So you can significantly reduce the water consumption by the meter, and with it the money of the family budget.

How to save water?

To make the bottle in the cistern even more useful, make a couple of small holes in it - in the lid and on the sides. Add vinegar to the water you will fill the bottle with. Cleanliness and freshness will delight you! This method is so simple that it’s hard to believe. But comparing numbers in receipts, you will see how useful it is sometimes to arrange household changes for the better at home.

How to reduce toilet water consumption

The average toilet cistern holds 8-9 liters of water. For flushing, 6 liters are enough. This difference is easy to fix with your own hands.

After placing the bottle in the cistern, Miss Clean magazine advises to check if the toilet flushes well. If there is not enough water, it is recommended to choose a smaller container.

Important: What you shouldn't do is put bricks in the cistern. It tends to dissolve, and this is fraught with clogging of the sewage system.

"Rush hour"

Residents of apartment buildings are familiar with pressure drops, when at certain times of the day the pumps operate at higher power, providing water to the upper floors. Adjust the float during these times (when the head is much higher than at other times).

Fix the float a couple of centimeters lower than usual

During the minimum pressure, the lever will cut off the water a couple of centimeters below. By fixing the valve, the tank can be operated without problems even with a long and weak filling.

Conclusion

Saving water resources is a very important problem in modern society and the point is not even to reduce monetary costs. Each of us understands that natural resources are not unlimited and the time will come when the earth's water resources will simply run out. In order to preserve everything that is filled with the bowels of the Earth for as long as possible, you need to make a personal contribution to their preservation. Saving water is the easiest way that a person can use to save it, because water is the source of life for everyone living on this planet.

In the next video, we'll look at another popular way to reduce water consumption.

How to remove a blockage in the toilet
We clean gas water heater do it yourself
How to properly install the toilet with your own hands
Wall-hung toilet with bidet function

Judgment day comes every month, bringing some upsetting. Paying the bills again? Constantly increasing utility rates despair even those who make good money.

Nobody wants to overpay! In such conditions, the most reasonable solution is to save ...

By saving water and electricity, you will not only do a good deed, while preserving the environment. Water reserves on the planet are not endless ... The method that you will see in the video will help you save a couple of tens of liters of water per month without any effort. You just need to open cistern and put a plastic bottle filled with water there.

How to save water?

Water, but never skimp on goodwill! Recommend this video to your friends, it is very relevant now.

Water is perhaps one of the main natural treasures, without which life on the planet is simply not possible. And most city dwellers will clarify a little: life is impossible without tap water. After all, it is even difficult for a person who has been accustomed to the benefits of civilization from childhood to imagine that once, in order to simply wash, it was necessary to complete a whole procedure - a morning trip to the well. This is probably why people with a central water supply are less inclined to think about saving water than those who have to carry it in buckets. That is why our article is aimed at happy users of water supply networks, whose happiness is darkened only once a month: on the day when water bills come.

So, although the famous advertisement insists that "the morning does not start with coffee," in fact, things are a little different. We wake up and go to the toilet. Everything is clear in the toilet - a toilet bowl and a cistern. Is it possible to save water here? Can!

Replace the tank with a more modern one - with two water drain buttons. For small businesses, less water is released, for large ones, respectively, more. The volume of the tanks is different and may depend on the model and brand of the manufacturer, but on average it is 6-8 liters. So on one "half" descent, you can save 3-4 liters of water.

You can simply put a brick or water bottle inside the tank to reduce its volume. But then it will be necessary, if necessary, to drain the water several times. An interesting way The implementation of the idea was presented by the California-based startup Drop-A-Brick, in which it was proposed to use a rubber brick filled with a hydrogel instead of a real one. An easy and cheap "substitute", according to its developers, is able to save about 2 liters on each discharge and up to 11,000 liters per year for one household.

And, of course, you need to make sure that the tank does not let water through. If water constantly leaks even in a very thin stream, then its losses can be quite large - up to 100 liters of water per day! It happens that the stream of water flowing out of the tank is so small that it is impossible to notice it, so you can learn about it empirically: you need to put a tablet of a cleaning agent in the drain tank overnight, which stains the water blue (or any other) color. And in the morning, check - if the water in the toilet has acquired a blue tone, then the water is leaking.

There are also quite radical solutions. Toilets with a sink for washing hands built into the cistern are gaining more and more popularity, especially in European countries. In this case, the water that is used for washing hands does not go straight to the sewer, but is collected in the cistern and then used to clean the toilet. If there is not enough water, then the tank gets it from the water supply system. This method is not only economical, but also convenient and hygienic: there is no need to go anywhere to wash your hands - everything can be done “without leaving the checkout counter”.

But while in Ukraine it is quite difficult to purchase such a kit, and therefore we will move to the bathroom.

The first thing to consider here is the mixers. The most economical option is a single-lever ball mixer. Its main difference from the usual tap is that when you add, for example, hot water, and turn the lever, it shuts off the supply cold water for the same amount that you added hot. And in the case of using a conventional tap, you simply increase the amount of water that continuously flows from the tap.

Very important point to save water is the installation of aerators on taps. An aerator is a device that "mixes" air into the flowing stream of water. It looks like a small mesh nozzle, something like a thimble, which is put on directly on the tap, and you can buy it at any plumbing store. Depending on the model, it saves 10 to 40% water by maintaining a good head, while reducing the volume of incoming fluid. On the soul, it must also be installed.

And now a few tips on how to save water, using which you can significantly reduce your water consumption, without spending a single penny.

Turn off the water when brushing your teeth, because in 3 minutes up to 30 liters can flow out of the tap. Use a regular 200 ml beaker for this procedure. Also turn off the water during shaving and other beauty treatments. With this approach, the “resulting consequences” are obvious: water savings can be up to 10 thousand liters per person per year.

Baths differ in spaciousness, but on average it ranges from 140 to 250 liters. Think, is it worth spending about 200 liters of water every time, if you can take a shower and spend about half as much? Especially if you remember to turn off the water when you lather your body, wash your hair or apply a scrub. At the same time, if you want to relax, warm up and spend a long time in warm water, then it will be more economical to take a bath.

After the morning water procedures, we go to the kitchen for breakfast. Our taps are already in order - they are serviceable, do not leak, equipped with a ball mixer and an aerator. In order to boil water and drink a mug of invigorating tea, put a kettle on the stove, but pour only the required amount of life-giving moisture, no more! This will allow us to save not only water, but also electricity or gas.

For washing fruits, however, like vegetables, it is better to use a bowl instead of running water. It is also better to use a large cup for washing dishes - washing it under running water is a waste! If possible, close the water drain in the sink and wash the dishes right in it. In a minute, from an open tap can "fly into the pipe" from 5 to 15 liters. But rinsing the dishes from detergents stands under running water. Just do it in quick movements, while reducing the force of the pressure.

But the most economical option in terms of water consumption for washing dishes is a dishwasher. Its advantage over by hand consists in the fact that the cleaning water circulates inside the machine itself, and is not constantly drained / collected. But when using the device, remember that it will work most efficiently when it is fully loaded. So don't turn on the dishwasher when there are only a few plates in it. Completely "equip" the car with both the dinner service and the services left over after breakfast or dinner, and only then press the "Start" button. And so that food residues do not dry out on the plates, you can use the "rinse" mode, which is in every dishwasher. Water consumption in this mode is 2-3 liters, and electricity consumption is 0.1 kW.

Some of the tips may scare you because they require you to change some habits. There is no need to be afraid: psychologists have statistics that it takes only about 3 weeks to develop a new habit. Calculate how much water you can potentially save during this time - and start fighting water waste immediately! Also, remember that water conservation is your contribution to conserving natural resources for your children and future generations.

Video: Toilet flush limiter (water saving up to 50%)