How to make a welder's table with your own hands. We equip the workplace by making a do-it-yourself welding table from a profile pipe with drawings and a photo Welding table for welding

Reading time ≈ 4 minutes

A compact do-it-yourself welding table will allow you to organize your workspace and save space. Thanks to the small design, the inverter and the supply cables can be conveniently placed without the risk of mechanical damage. Additionally, a ready-made table is quite realistic to use for welding. Due to the built-in wheels, it is possible to move the table assembly to any convenient place.

Required tools and materials

Make a welding table from shaped pipe, as in the photo, you can do it yourself without using special equipment. It's enough to have everything necessary materials and a minimum set of garage tools, in particular a grinder, welding, measuring angle, jigsaw, drill and vice.

The design dimensions of the table according to the drawings in the article are: 370x580x780 mm, however, depending on the need, you can use your own dimensions.

Step-by-step instructions for making a welding trolley

1. Making the top table cover... The metal table for welding is equipped with a lattice cover, which is made of a profiled pipe with a cross section of 50x50 mm (for the outer frame) and 30x30 mm for the inner lattice. The pipe is cut to size with a grinder. The prepared elements are connected by welding. The outer belt of the cover consists of a 50x50 mm profile, which is welded into a rectangle, taking into account the design dimensions. Inner space filled with a 30x30 mm profile. The pipes are welded after 30-50 mm, forming a grid. Welding seams must be cleaned with a grinder.

2. Making table legs... The legs for the welding trolley can be made from round pipe section 25x25 mm or 30x30 mm. In the absence of these dimensions, the use of 20x20 mm is allowed. Materials are cut to size (780 mm). A total of 4 metal legs are required. The cut elements are welded to the finished lid at the four corners.

Important! When welding the legs to the lid, it is important to control the skew. To get the most stable table, it is necessary to ensure even installation angles and the location of the racks. It is recommended to use a square and tape measure.

3. Additional rigidity belt for the table. Metal trolley for welding machine should be as tough and durable as possible. To do this, it is necessary to make an additional stiffening belt, which will be located at a height of 200-300 mm from the floor level along the racks. The amplifiers are made of a 30x30 mm corner, which turns outward with an acute angle. The elements are welded in a circle to connect all 4 posts. If necessary, you can additionally grind all welds.

4. Making a handle for lifting and transportation. The handle is necessary to conveniently transport the table to any specified location. For the handle, you can use a metal bar or reinforcement with a cross section of 8-10 mm. It is important to initially give the desired shape to the element. In the future, as seen in the video, the finished handle is welded to the supporting frame of the top cover. It is necessary to weld the handle from below in order to avoid further inconvenience during the operation of the table.

5. Hooks for welding equipment or cables. Side hooks are essential for conveniently securing thick cables, holders, or storing any other welding tool. Hooks can be made from an ordinary nail 100-150 mm. To do this, it is enough to give the desired shape to the nails and weld them to the supporting legs from the outside.

6. Wheels to move. Wheels are necessary for more convenient movement of the table to a convenient place. In total, you will need 2 wheels assembled with fastening mechanisms. It is most preferable to use small parts from a shopping cart or similar equipment. Before installation, the top of the locking mechanism with the nut must be welded to the uprights. Next, the wheels are screwed onto the welded nut.

Important! Weld the fastening nuts for the wheels, taking into account the horizontal. The details should be on the same level.

7. Niche for tools. The niche should be made of plywood, chipboard or OSB boards. If necessary, you can use a solid sheet of metal. The material is cut to size with a jigsaw and placed on the corners at the bottom of the table.

8. Protective cover from debris and scale. For manufacturing, you can use common leaf metal of any thickness with a bend around the edge. Beforehand, a metal bar of 8-10 mm is welded to the supporting legs, while one side must be higher than the other in order to create the required slope. The cut metal sheet is mounted on rods.

In order for the weld to be neat and durable, the work is comfortable and safe, the welder needs a well-equipped workplace... Working on random supports or on the floor does not make it possible to conveniently position the welded parts and fix them securely. For this, equipment such as a welding table is intended. It can be purchased ready-made, or you can do it yourself.

Welding table requirements

Before starting to design and manufacture a welding table, it is necessary to determine the requirements for it:

The rigidity of the structure. It should not "walk" under the weight of massive or bulky welded structures.
Reliability of fastening of workpieces.
Convenience of the welder's work.
Shelves for welding equipment, welding consumables.
A box for rarely used tools.

In addition to the basic requirements, additional options can be provided:

exhaust ventilation to remove welding gases;
lighting working area- 36 volts or LED.

In addition, it is important that no flammable materials are used.

Welding table drawings

You can make a welder's table according to industrial drawings. However, they are usually overloaded with technological and production information that is irrelevant for home master... A sketch drawing can be done independently, the main thing is to accurately calculate and designate both the overall dimensions and the dimensions of each workpiece.

When designing a welding table, its height is torn out slightly below 80 cm - then the welder will be in the most convenient position for work.

Required tools and materials

In a home workshop, they often strive to get by with scrap materials. However, in order to meet the strength and stability requirements formulated above, the following should be used for racks:

profile with a cross section of at least 60 × 60 mm and a wall thickness of 4 mm;
I-beam or corner 60 × 60, but already with a thickness of 4 mm.

The shelf and drawers can be made from a lighter profile.

The table top is taken from profile rolled products. The gaps between them will be used to fix the parts to be welded with clamps or pliers.

For a protective screen, apply:

base frame - light profile;
the screen itself is a metal sheet of 0.4-1.0 mm.

The side bumpers are also made at the protective screen.

A welding table with a fastening system should be equipped with additional devices that help fix the workpieces to the table and to each other:

clamps;
clamps;
magnetic plate base for attaching small parts.

You cannot make this equipment for a welding table with your own hands, you will have to buy it.

Welding table structure

There are several types of designs. The most common are:

amateur, for occasional welding, small structures by a home craftsman;
semi-professional assembly and welding, for complex operations

For a table made of a profile pipe, made by hand, the following sizes are recommended:

the height of the working surface from the floor is 70-85 cm;
dimensions of the working surface not less than 80 × 100 cm;
the height of the protective box is at least 140 cm from the floor.

Simple welding table

This design is durable, easy to manufacture, and easy to use for small amounts of welding. It consists of hard-welded metal frame from a 60 * 60 profile. Four racks are attached to it. At 20 cm from the floor, they are connected by corners 20 * 20. On top of the frame, tabletop elements are installed, forming a reliable support for the workpieces to be joined and provided with grooves for their fastening.

Hooks for wires from the welding machine are welded to the frame, a shallow pan for scale and dust is placed under the working surface.

On one side of the table for welding, a cabinet is installed made of a thin metal sheet for storing small tools. Here I weld a stand for a water tank.

Semi-professional welder table

It is a welding and assembly station designed to improve the convenience of welding. Allows you not only to cook, but also to carry out the accompanying machining.

This table provides:

rotary work platforms;
installation of drilling or milling equipment;
quick-detachable locksmith vice;
rotary attachments for fastening the welding machine;
exhaust ventilation;
flexible illumination of the working area;
anchorage to the concrete floor.

The purpose of all these improvements is to enable the welder to work from a comfortable, non-tiring posture and save time on the operation of removing and placing the product on the post. Pay off with large volumes of work

Manufacturing of a welding table

Let's take a closer look at the production process of a simple do-it-yourself welding table. It is made of a rectangular metal profile and a corner. Sizes can be changed depending on the needs of a particular home craftsman.

Decide on the size of the table

For free placement of workpieces, convenience and safety during work, we choose the following dimensions:

the height of the floor countertop level - 75 cm;
tabletop dimensions - 80 × 100 cm;
the height of the protective screen is 140 cm from the floor.

Procurement and cutting of material

For the manufacture of the structure you will need:

corner 25 × 25, length 46 cm, ends cut at 45 ° - 4 pcs .;
corner 25 × 225, length 76 cm, ends cut at 45 ° - 4 pcs .;
profile 30 × 230 × 21.5, length 76 cm - 4 pcs. (for legs);
steel sheet 3 mm 44.5 × 75 cm - 2 pcs. (for shelves);
profile 60 × 240 × 22 mm - length 100 cm - 2 pcs .;
profile 60 × 240 × 22 mm - length 72 cm - 2 pcs.;
profile 40 × 230 × 21.5 length 72 cm - 8 pcs. ;
swivel wheel support with stopper - 2 pcs .;
wheel support - 2 pcs.

The rolled metal is cut with a grinder or a cut-off saw, carefully deburred.

Countertop manufacturing

Along the contour, the tabletop is made of a 60x240 profile. When assembling, make sure that the corners and diagonals of the contour are equal.

The inner lattice is made up of 30x230 profile sections and welded to the contour at equal distances from each other. All welds should be carefully cleaned with an angle grinder.

On the side of the short sides, handles from a bar of 8-12 mm can be welded to the bottom of the tabletop. This will allow you to move the table from place to place.

The legs are welded to the corners of the tabletop frame. First, grab the legs with spot welding and especially carefully check the installation angles of the legs with a charcoal and a metal ruler. They must be strictly perpendicular to the plane of the frame. If a misalignment is found, it should be corrected. Otherwise, the table will be unstable. From the bottom of the legs, you can weld the wheel mounts. This is convenient if you plan to move the table frequently from place to place. If the place is constant, then it is better to abandon the wheels that add instability and weld small squares of metal to increase stability and protect the floor from damage.

After leveling the legs, they must be welded constantly and fastened with additional strapping from light corners 20 cm from the ends. They are welded with the flat side down, and an OSB shelf is placed in the formed recess. Welding equipment and materials, a mask, etc. are placed on it.

Several brackets and hooks can also be welded to the legs for hanging cables, a holder and other accessories. They are made from a steel bar of large nails. They should be carefully cleaned to remove sharp edges.

Protective box

The protective box is used to prevent the spread of molten metal splashes during welding and solid waste during cleaning. The frame is made of a light corner, and the box itself is made of thin sheet metal. It attaches to the table top with pins. When working with parts protruding beyond the dimensions of the table, the box is removed.

A tray with low sides can be welded under the worktop to collect scale when cleaning seams. The tray is installed with some inclination so that the debris gradually collects to its lower edge.

The tools are stored in a wooden or metal box. Instead, you can weld a cabinet with shelves.

Assembly

For assembly work you will need:

welding machine;
electrodes;
Bulgarian with cutting disc and a disc for stripping;
a set of hand-held locksmith tools;
ruler 1 m, corner, tape measure.

The assembly is carried out in the following order:

cutting blanks, checking dimensions and angles according to a sketch drawing;
assembly of the table top: first the outline, then the ribs;
attachment of legs;
welding of the lower strapping;
fastening wheels or support pads;
assembly of the protective box;
installation of the tray;
final cleaning of seams, burrs and irregularities;
applying primer and paint;
installation of OSB sheet.

Additionally, you can weld on handles and hooks for wires.

Precautions when working at the welding table

Welding has several harmful factors that can damage human health:

heat;
scattering of hot splashes;
high intensity ultraviolet radiation;
electric shock;
falling of heavy objects.

To avoid harmful effects, the following rules should be observed:

Work should be carried out in well-ventilated rooms equipped with both supply and exhaust forced ventilation.
Before starting work, carefully inspect the equipment for mechanical damage, insulation faults, loose contacts.
During work, it is imperative to use personal protective equipment: a welder's mask, a respirator, split-leather protective gloves with gaiters, fire-resistant clothing and shoes.
The workplace should not be cluttered. Easy and convenient access for the welder to the working area should be provided.
It is strictly forbidden to work from accidental supports.
The parts to be welded should be secured with inventory fasteners.
It is strictly forbidden to use and store flammable materials and liquids closer than 5 meters from the welding place.

Careful implementation of these rules will preserve health, life and material values.

In a home welding workshop, sometimes you simply cannot do without such a necessary device as a welding table. Such a structure, made of metal, greatly facilitates the process of welding various assemblies, parts and structures. except bearing function The welder's table can act as a ground loop to which a clamp and a grounding cable can be connected. The welder's table can be either purchased in specialized stores or made on your own, saving a certain amount of money. Self-assembly will be a great practice and will be beneficial for aspiring welding professionals.

It is better to make a welding table with your own hands, as it will benefit the novice welding specialists.

The main functions of the welding table

Welder's table - enough simple construction, which performs the following main functions:

work plane, equipped, among other things, with various elements for fixing workpieces (grates, ladders, welding torch holders, etc.);
ground loop.

Tools and fixtures for creating a welder's table

To create a welder's table, you need the following tools and materials:

a welding machine, as well as electrodes, an inert gas cylinder, etc.;
regular square;
joiner's square;
construction tape;
nippers;
C-shaped clamps - 4 pcs.;
saw for metal (grinder);
tap for threading M8;
drill or hammer drill;
equipment for chamfering from workpieces (milling or lathe).

Safety requirements for the production of welding

Welding works are classified as high-risk work, therefore, during their production, the following basic labor protection and safety requirements must be met:

Welding work should be carried out in a well-ventilated room or room with supply and exhaust ventilation.
When working, you need to use personal protective equipment: a welding shield or a mask, leather gloves for welding, overalls, safety shoes.
Before starting work, it is required to check the serviceability of welding equipment, grounding and personal protective equipment.
The welder's workplace must be free of flammable materials and free from obstructions.

Welding table assembly algorithm

Option 1. Drawing of the welding table.

As an example, consider two options for creating a welder's table with your own hands.

Welder's table 1100x660x900 mm. To facilitate and reduce the cost of construction, the tabletop is made of a sheet of thick plywood, which is subsequently covered with a metal plate.

Materials for assembly:

profile pipe 40x20x2 mm - 9.9 m;
strip 40x4 mm - 2.0 m;
fasteners: bolts М8х40 - 4 pcs. nuts М8-6 - 4 pcs .;
steel sheet 1100x650x2 mm - 1 pc .;
plywood 1220х1220х10 mm - 1 sheet.

We cut blanks for the frame, legs and lintels of the table from a 40x20x2 mm profile pipe (2 blanks 1.1 m each, 2 blanks 0.66 m each, 4 blanks 0.9 m each, 1 blank for a frame lintel - 0.58 m, 2 blanks for lintels for table legs 0.58 m each, 1 blank for long lintels for table legs - 1.02 m).

We remove chamfers on the parts to be welded on a milling or turning machine.

We cook the frame under the table top:

The blanks of the profile pipe, intended for welding the frame for the table top, are placed and fixed with C-shaped clamps on a large flat table.
The frame for the countertop is a rectangle with a jumper, therefore, for correct assembly and further operation of the structure, we check the coincidence of the sizes of the two diagonals of the rectangle. Permissible deviation ± 1 mm.
We weld the workpieces under the frame (first of all, we weld the rectangle itself, and then the jumper), first with a tack weld, we check the geometric correctness of the connection, and then we weld all the joints with the main seam.
We clean the seams with a grinder.

We reinforce the corners of the tabletop frame with strips of 40x4 mm for attaching legs and other hanging elements. For this:

we remove chamfers on prepared overlays;
We weld the prepared overlays from the bottom of the frame in the corners of the table legs.

For fixing the legs, we weld overlays from a 40x4 mm strip (with a preliminary beveled) to the upper edge of the legs, make holes for attaching the legs with a drill or punch:

drill holes D<6 мм в ножках, затем по ним размечаем и сверлим отверстия в раме;
we drill holes to D = 6.7 mm and cut M8 threads.

We attach the table legs to the frame and weld the side bars between the legs.

Cut out a tabletop from a sheet of plywood, install it on the frame and cover it with a steel sheet. If necessary, fix the layers of the tabletop to the frame.

We treat all seams with anti-corrosion compounds.

In the future, it will be possible to modernize this table by attaching wheels for movement with locking devices to the legs, and install additional elements for fixing workpieces: ladders, gratings, etc. You can weld a welding torch holder made from a piece of pipe of the corresponding diameter to one of the top corners of the tabletop. This version of the table is spacious enough, solid and suitable for working with massive structures.

Welder's table 445x750x915 mm. This table is compact in size and has castors (with locking devices) on legs.

Option 2. Drawing of the welding table.

Materials for assembly:

metal plate 445x750x3 mm - 2 pcs .;
corner 25x25x3 mm (46 cm long), cut at 45 ° - 4 pcs.;
corner 25x25x3 mm (76 cm long), cut at 45 ° - 4 pcs.;
corner 32x32x3 mm (91.5 cm long) - 4 pcs.;
pipe D = 3 cm (7.5 cm long) - 1 pc .;
wheel threaded supports - 4 pcs .;
nuts for wheel supports - 4 pcs.;
connecting nuts - 4 pcs .;
lock washers - 4 pcs.

All materials must be free of rust. If there are traces of corrosion, they must be thoroughly cleaned.

We weld the frames for the countertop and the second shelf. We make two equal rectangles with sides of 76 cm and 46 cm. We check the coincidence of the sizes of the two diagonals of the rectangles. Permissible deviation ± 1 mm.

First, we weld the frame blanks with a tack weld, check the geometric correctness of the connection, and then weld all the joints with the main seam.

We clean the seams with a grinder. We weld the tabletop and the second shelf to the frames, weld first with a tack weld, and then with the main seam.

We weld the table legs to the frame with the table top. With the help of clamps, we fix the legs, attached at an angle of 90 ° to the frame with the table top, weld the joints with a tack weld.

Similarly, we fix and weld the legs to the second shelf, located at a selected distance from the table top (usually 0.7 m). After checking the rectangularity of the joints, we carry out all the seams with the main welding seam. We mount the wheel supports.

We weld the holder for the welding torch (pipe L = 3 cm, 7.5 cm long) to the selected corner of the table top.

We treat all seams with anti-corrosion compounds. The second version of the welder's table is ready.

It is characterized by mobility and takes up little space, suitable for work in a small workshop.

Every master, more or less seriously engaged in welding, knows how difficult it is to assemble complex structures of a large size alone. Even an ordinary rack for a garage or basement is quite problematic to make - to set the frames on a level, fix them, make an oven mitt. A do-it-yourself welding table will help out here, which is completely easy to make even for a novice welder.

It is a simple yet extremely functional design that allows you to perform most welding (and metalworking operations) with great convenience. It is only important to do it correctly. You can use ready-made drawings from the Internet or special welding manuals, or develop your own, based on typical ones. For a real master, the second option is better - you can always make changes to the design, taking into account:

terms of use of the table,
place of its installation,
types of work to be performed,
anatomical features of the welder.

The role of the welding table is to increase the comfort of the welder and, as a result, the speed and efficiency of work. In most cases, this is also possible when using a standard table, purchased or made according to ready-made drawings, but your own design is still preferable.

Below are photos that are mass-produced or made independently by different craftsmen.

As you can see, there can be several design options, among them:

stationary;
prefabricated;
mobile;
folding.

The main thing that unites them is that they are all made of metal, very durable and equipped with a dewy horizontal table top, with holes or gaps between the strips. Such technological openings are necessary for free ventilation of the working area, for the fall of sparks and slag, without stopping welding to clean them and to facilitate the structure of the table.

To build a do-it-yourself welding table, you need to have some electrode welding skills (otherwise why a table?). Of course, it is possible to assemble the structure on bolted joints, in this case you only need a grinder and a drill, but nevertheless, a welded table of your own work is a kind of visiting card of a welder, even if he works exclusively for his own pleasure.

An approximate drawing of the welding table is shown below - you can focus on the dimensions and features of the device when developing your design, but changes are possible, even desirable.

First of all, they touch the table legs. The illustration shows the supports at an angle. This is practical and justified for a large table where it is necessary to properly distribute weight, especially if there is a large part or a complex structure on the table top. For a home workshop, vertical legs perpendicular to the table top are justified - and it is more convenient to cook such a table, and it is not inferior in functionality.

The central support is necessary if the length of the table exceeds 2 m. In the case of smaller sizes, two pairs of legs are sufficient - the table frame from a 4x4 cm corner is able to withstand fairly decent loads distributed over the entire area. But rollers, especially swivel ones, are a very necessary thing. You can use furniture made of hard plastic, or look for metal ones. It is not difficult to make them yourself on the basis of 203 bearings.

The table can be rotated around its axis as desired. But their position must be fixed, and at least two of them, on the legs located on the diagonals, are equipped with a holding brake. Maneuverability of the table is not always required when it starts moving completely unexpectedly with little effort or careless movement.

Table mounting

We will not dwell in too much detail on the installation operations - this is the priority of the master who intends to assemble the table. But we will briefly describe the basic operations, tools and materials.

To assemble the table, you will need the following tools:

Welding machine (MMA or semi-automatic);
Bulgarian;
Clamps;
Drill;
Pliers;
Level;
Square.

Of the materials, a square of at least 4X4 is required for the legs (you can use a rectangular or square profile pipe) and the table frame. If the frame is made with two or three internal longitudinal spars, then you can limit yourself to a corner or a 3x3 cm pipe, but for the legs it will be clearly insufficient.

The amount of metal is determined by the dimensions of the table, which are selected by the master. The height of the table should be within 0.7-1 m, depending on the height of the welder. When cutting blanks, it is necessary to take into account the height of the supports - swivel rollers or height-adjustable supports (installed on stationary tables.

For the worktop, steel plates made from sheet with a thickness of 3 mm (max. 6 mm) are required. Thicker metal is not required for a table in a home garage or for a small workshop. If it is possible to buy a perforated steel sheet with holes of any configuration, with a diameter of at least 1 cm, then this is even preferable - the strength of the table becomes higher, installation is simplified and the plane of the tabletop will be very flat, which in many cases will allow you to perform rather complex welding operations.

Wooden parts should be avoided even as an aid. Welding work is not for combustible materials in the structure. If the weight of the table does not matter, which is justified with stationary options, then parallel to the tabletop, 10-15 cm lower than it, you can weld another shelf frame, which serves for storing various materials - a corner, a profile, reinforcement and round timber. The workshop will not be cluttered with material and all of it will be at hand.

How to make a welding table yourself one of the most convenient designs is shown in the video.

If you have your own developments in this area, or your already built welding table, share information with us and our readers. Practical experience is the most valuable thing the Internet has.

When welding small-sized parts, problems with their fixation arise. Subsequently, they will affect the quality of the seam, the reliability of the connection. For the solution, special tables are made, the design of which is designed to improve the convenience of the welder. It is important to choose the right drawing and draw up an assembly diagram.

Table drawings

The problem of self-fabrication of a table for welding is the minimum information about such structures. Factory models cannot serve as a basis for drawing up a drawing, since they are complex, many functions are inapplicable in a home workshop. The alternative is to take the simplest drawing as a basis and improve it.

do not install casters, as they will affect stability;
make longitudinal slots (30 mm) on the working welding surface with your own hands to fix the clamps;
install an inclined plate under them to protect the tool from sparks and scale;
installation of lifting sidewalls to increase the working surface of the table.

As a result, you should get a similar device for welding:

Materials and components

For manufacturing, you can use any available metal-roll - corners, pipes of a profile section, sheet material. It is important that the welder's table is stable, withstands not only the weight of the workpiece, but also the possible increase in pressure on the surface during operation.

Tips for choosing materials:

Support legs (legs). They are made of a profile pipe or corner, the first option is preferable, since the mechanical strength increases. Thickness - from 1.5 mm or more;
Working welding surface. Steel plate with slots for clamps, thickness - from 2 mm. The edges are rounded to create a flat surface.
Additional designs to increase the working area of the table from square or round tubes.
The protective screen is made of sheet iron, preferably with sides.
The lower shelf is made of fiberboard or chipboard. For better protection, you can put a thin sheet of steel.
Stiffeners - corners or pipes.

Additionally, you will need a primer and paint. It is better to process the desktop - this will increase its service life.

Assembly order

To carry out the work, you will need a welding machine, electrodes, a grinder with discs for metal, a measuring tool, and bolts for fastening. A preliminary drawing of the structure is drawn up, the dimensions of the blanks are calculated. In the latter case, the thickness of the weld must be taken into account.

Assembly instruction:

Formation of blanks, checking their dimensions according to the drawing.
Assembly of the frame, welding of support posts, fastening of stiffeners.
A worktop is made according to the dimensions of the finished frame. After measurements, it is not fixed.
Installation of a protective screen. The angle of inclination is up to 45 °, an additional chute is made for pouring welding waste.
Installing the main work surface.
Manufacturing of sidewalls, they are attached to the structure on hinges. Movable stops made of small diameter pipes.
Priming and painting.
Installation of a sheet of fiberboard or chipboard.

Additionally, hooks, boxes or boxes for storing and fixing the tool can be installed on the welder's table. The choice depends on the requirements for functionality and usability.

What else is needed to complete

To create the most comfortable working conditions, you will need to buy additional tools for the welder. Their function is reliable fixation of the workpiece, the ability to quickly change the position. Requirements - resistance to temperature drops, mechanical strength.

A set of additional tools:

Clamps. Required for fixing the workpiece to the surface for precise welding;
Clamps. They perform the same function, but in a more specialized way - the installation needs a corner of the honey with the parts to be welded, a complex connection.
Magnetic base. Recommended for processing small parts, which are difficult to fix mechanically.

In the latter case, the weight of the magnetic auxiliary tool and the maximum allowable weight of the workpiece must be taken into account.

The video provides a detailed overview of the optimal table model for a welder: